Plate straightening machine, sheet metal forming, roller feeder feeding step (MAC3-600)
http://www.ruihui.net
Roller feeder feeding step test method:
1. Use the inching operation to stop the punch at the bottom dead center position, mark the material, and then punch the sheet once, and mark the material.
After repeating this several times, the measurement is performed, and after comparing with the required feeding step, the adjusting screw is re-adjusted according to the demand to reach the required feeding distance.
2. Inching operation punching machine, let the punch output shaft drive the roller feeder to feed the material into the punching die, ensure that the punching machine punches the guiding hole, and then injects to the punching machine more than 3 points, the guiding pin and the guiding hole The position was compared and determined.
If the position of the guiding pin and the guiding hole are correct, it means that the step setting is correct, if it is not correct, it needs to be re-adjusted.
3. When measuring the feeding step of the roller feeder, pay special attention to the inability to use the inching operation to stop the punch at the top dead center position measurement, because when the punch slider stops at the top dead center position.
Feeding is not completed, usually only sent half, so each stop position will be different, the adjustment of the feeding step can not be measured correctly, so make sure that the punch slider stop position exceeds 3 o'clock position when measuring.
Specification:
| Model | MAC2-400 | MAC2-500 | MAC2-600 | MAC2-800 |
| Stock Width(mm) | 50-400 | 50-500 | 50-600 | 50-800 |
| Stock Thickness(mm) | 0.3~3.2 | 0.3-3.2 | 0.3-3.2 | -3.2 |
| Max.Coil Weight(kg) | 3000 | 3000 | 3000 | 5000 | 5000 | 7000 |
| Max.Coil O.D.(mm) | 1200 | 1200 | 1200 | |
| Coil I.D.(mm) | 8 | 8 | 508 | 508 |
| Feed Length(mm) | ~500* | ~500* | ~500* | ~500* |
| Max. Line Speed(m/min) | 16-24 | 16-24 | 16-24 | 16-24 |
| Work Roll Number(pieces) | upper 6
lower 5 | upper 6
lower 5 | upper 6
lower 5 | upper 6
lower 5 |
| Feed Roll Number(set) | 1 | 1 | 1 | 1 |
| Main Motor(kw) | AC2.9 | AC2.9 | AC4.4 | AC4.4 |
| Mandrel Expansion | hydraulic | hydraulic | hydraulic | hydraulic |
| Reel Motor(kw) | 1.5 | 1.5 | 1.5 | 2.2 | 2.2 | 3.7 |
| Power(V) | 3 Phase 220V/380V/50HZ |
| Operating Air(Mpa) | 0.49 | 0.49 | 0.49 | 0.49 |
Straigtening performance:
| tock Thicknees (mm) | Stock Width (mm) |
| 0.3 | 400 | 500 | 600 | 800 |
| 0.4 |
| 0.6 |
| 0.8 |
| 1.0 |
| 1.2 |
| 1.4 |
| 1.6 | 470 | 470 |
| 1.8 | 400 | 400 |
| 2.0 | 360 | 360 |
| 2.3 | 300 | 300 | 300 | 300 |
| 2.5 | 230 | 230 | 230 | 230 |
| 2.8 | 150 | 150 | 150 | 150 |
| 3.2 | 110 | 110 | 110 | 110 |
*1:(Pneumatic):Option in case of pneumatic mandrel expansion is provi
1. Pre-Sales Service:We have professional designers to meet the different requirement of our customers.
2. After-Sales service:We have an efficient team to meet 24*7 all day service.
3. Full-Service:Actively cooperate with customers to deal with problems in equipment using.
4. Engineers can provide service machinery overseas.
Product Tags:
|
|
Energy Efficiency Steel Plate Straightening Machine Semiautomatic Feeder Images
|
